Spindle Cutters

Spindle cutter - Quarter round 3/8' and Bead 1/4'   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter can be configured to cut quarter rounds and beads KP800020 - 3/4' - 1/2' spacer rings   Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - Wedge Tongue   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter is used to make a tongue and groove and matches up with KP13 KP800020 - 3/4' - 1/2' spacer rings   Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - Wedge Groove   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter is used to make a tongue and groove and matches up with KP12 KP800020 - 3/4' - 1/2' spacer rings Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - Quarter round 1/4' and 1/2'   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter can be configured to cut quarter rounds KP800020 - 3/4' - 1/2' spacer rings   Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - Ogee   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter can be configured to cut ogee profiles. KP800020 - 3/4' - 1/2' spacer rings   Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - Glue joint (single F-joint)   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter is a counter-profile cutter. When properly aligned, it will allow two panels to join together without the use of a secondary cuttter. The F-profile assists with alignment during assembly and adds a greater glue surface, resulting in a stronger joint. KP800020 - 3/4' - 1/2' space..

Spindle cutter - Cove 3/4'   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter can be configured to cut coves, flutes or beads. KP800020 - 3/4' - 1/2' spacer rings   Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - Straight/Slot/Rabbet 3/4' Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter can be configured to cut grooves/slots and rebates. KP800020 - 3/4' - 1/2' spacer rings Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - Reversible Rail & Stile Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter is used in door manufacturing to profile and join the rails and stiles. For example: Kitchen cabinet doors. KP800020 - 3/4' - 1/2' spacer rings Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped wit..

Spindle cutter - Full bead/Half round/Bull nose 3/4'   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter can be configured to cut full beads, half rounds or a bull nose. KP800020 - 3/4' - 1/2' spacer rings   Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spin..

Spindle cutter - 3 lip classic bead   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter can be configured to cut quarter rounds and coves KP800020 - 3/4' - 1/2' spacer rings     Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindle shaft.....

Spindle cutter - V - paneling Tongue & Groove   Tungsten Carbide - 3 wing The cutter is designed to be used with a stationary spindle moulder equipped with either a 3/4' or 1/2' spindle shaft. The cutter is used for joining paneling to form a 'V' groove. Great for ceilings. KP800020 - 3/4' - 1/2' spacer rings     Important: Make sure the spindle moulder has a table opening of at least Ø 140mm. Designed for spindle moulders equipped with either a 1/2' or 3/4' spindl..